Mortars
Mortar Mix mixed with water produces a workable, high quality mortar that is ideal where rapid strength gain, high durability and low shrinkage are desired. Apply Mortar Mix in thicknesses from 1/2-in to 6-in. Durable in wet environments. SETS IN 15 MINUTES & IS READY FOR TRAFFIC IN 1-HOUR. One 55 lb. bag of Rapid Set® Mortar Mix will yield approximately 0.5 cubic feet. Mortar Mix is a versatile product that can be used for general concrete repair, stucco & plaster repair, one-coat exterior plaster, mortar beds, underlayments, and formed work. Mortar Mix is suitable for vertical and overhead applications.
USE: General concrete, stucco and plaster repair, mortar beds, underlayments and formed work. For applications from 1/2” to 6”, sets in 15 minutes. Ready for traffic in 1 hour.
YIELD: Coverage depends on project size.
SIZE: 25 lbs. or 55 lbs.
Amerimix AMX 475 PSV Polymer Modified Stone Veneer Mortar is a high performance, polymer modified mortar designed with superior bond strength and ability to grout artificial stone on horizontal and vertical surfaces to concrete or masonry substrates.
FEATURES AND BENEFITS
• Factory blended under controlled conditions for mix consistency
• Superior bond strength
• Extended mortar board life, less re-tempering required
• Increased yield compared to typical field mix mortars
• Available in gray and buff
USES
• Interior or exterior applications
• Above or below grade
• Bonding of artificial veneer brick or stone
• For all masonry veneer work
Amerimix AMX 400 Portland Cement, Lime and Sand Mortar is a factory blend of portland cement, hydrated lime, and dried sand with a formulation engineered to provide long water retention, exceptional workability and superior bond strength over masonry substrates.
FEATURES AND BENEFITS
• Factory blended under controlled conditions for mix consistency
• High bond strength
• Extended mortar board life, less re-tempering required
• Increased yield compared to typical field mix mortars
• May be pigmented
USES
• Interior or exterior applications
• Above or below grade
• Laying or resetting brick, block and stone
• For all masonry veneer work
Sakrete® Stone Veneer Mortar is a high performance, polymer modified mortar designed to set and grout artificial stone on horizontal or vertical concrete or concrete masonry substrates. Available in Brown or Grey.
A polymer-modified contractor grade mortar specifically designed to adhere manufactured or artificial stones in vertical applications.
Polymer modified to improve adhesion of manufactured stones to substrate, especially in vertical applications.
Consistent quality from bag to bag means less waste and problems associated with on-site mixing.
Just add water.
Sakrete Glass Block Mortar is a contractor grade product designed for installing glass block or other applications where white mortar joints are required.
A quality blend of white cement, lime, sand and special additives for laying glass block, brick, block or stone where a white mortar joint is desired.
• Contractor grade mortar mix.
• Use where white mortar joints are desired.
• Reduces mold growth.
• Just add water.
Amerimix AMX 410 WRM Water Repellant Mortar is a factory blend of portland cement, hydrated lime, dried sand, water repellent and proprietary admixtures. This formulation is designed for applications where a water repellant mortar is required in combination with water repellant masonry units. AMX 410 WRM is engineered to provide long water retention, exceptional workability and superior bond strength over masonry substrates.
FEATURES AND BENEFITS
• Eliminates the need to stock liquid admixtures
• Factory blended under controlled conditions to ensure
that the accurate amount of repellant agent is
consistently mixed in every batch
• High bond strength
• Extended mortar board life, less re-tempering required
• Increased yield compared to typical field mix mortars
• May be pigmented
• Available in Type M, S, N (Type N for above grade use only)
USES
• Interior or exterior applications
• Above or below grade
Sakrete Surface Bonding Cement is a quality mixture of cement, lime, sand, fibers and special additives. Used to build, decorate and damproof dry stack concrete block walls. Can also be used to strengthen existing mortared or dry stacked block walls. Structural applications where safety is a concern should be designed and approved by a licensed engineer
Used to build mortarless block walls
• Water resistant, structural coating
• Reinforce existing masonry walls
• Available in white
• Just add water.
Amerimix AMX 400 Portland Cement, Lime and Sand Mortar is a factory blend of portland cement, hydrated lime, and dried sand with a formulation engineered to provide long water retention, exceptional workability and superior bond strength over masonry substrates.
FEATURES AND BENEFITS
• Factory blended under controlled conditions for mix consistency
• High bond strength
• Extended mortar board life, less re-tempering required
• Increased yield compared to typical field mix mortars
• May be pigmented
APPROXIMATE COVERAGE
One 80 lb. bag yields approximately .78 cu. ft and will lay up to 20 concrete blocks or 45 standard bricks with 3/8” mortar joints, or 17 sq. ft. of manufactured stone. One 3,000 lb. bulk bag will lay up to 750 concrete blocks or 1690 standard bricks.
USES
• Interior or exterior applications
• Above or below grade
• Laying or resetting brick, block and stone
• For all masonry veneer work
Amerimix AMX 470 Stone Veneer Mortar is a high performance mortar designed to set and grout artificial stone on horizontal or vertical concrete or concrete masonry substrates.
FEATURES AND BENEFITS
• Factory blended under controlled conditions for mix consistency
• Extended mortar board life, less re-tempering required
• Increased yield compared to typical field mix mortars
• Available in gray and buff
USES
• Interior or exterior applications
• Above or below grade
• Bonding of artificial veneer brick or stone
• For all masonry veneer work
Amerimix AMX 405 C Portland Cement, Lime and Sand Mortar – CUSTOM COLOR is a factory blend of portland cement, hydrated lime, dried sand and color pigment formulation engineered to provide long water
Sakrete Type S High Strength Mortar/Stucco Mix is a contractor grade product for laying brick, block or stone. It can also be used as a scratch or brown coat in stucco applications.